Selling Online Since 1996!

844-420-4100

Phone Orders Welcome

Technical Support

Free Design Service!

Fittings for Poly and Vinyl Tubing

All our fittings listed in a size will work with any tubing listed in the same size!

Fittings can be confusing with all the different sizes of tubing, then add in that if you bought tubing at a local store they may only call it 1/2" but give you no I.D. or O.D. for getting the correct fittings elsewhere. We can't tell you what you got someplace else but here is what you need to know for our tubing sizes!

All fittings have an I.D. or O.D. listed that they work with. Match this up with your tubing size and you're good to go!

I.D. = Inside Diameter
O.D.
= Outside Diameter.

1 - 16 of 226

Page:
  1. 1
  2. 2
  3. 3
  4. 4
  5. 5
  • SF011-05

    1/4" Barbed x 1/8" Barbed Connector

    Regular Price:

    $0.56 As low as: $0.53
    The 1/8" x 1/4" barbed connector is used to connect 1/4" microtube to 1/8" microtube or to connect 1/8" microtube to 1/2" or 3/4" poly tube mainline.The 1/4" barb inserts into a hole punched into the mainline and the 1/8" is placed over the 1/8" barbed end.Works with any 1/4" microtube that has an ID of .140 to .170 and any 1/8" microtube with an ID of .115 to .120.
  • SF009

    1/8" Barbed Connector

    Regular Price:

    $0.09

    1/8" Barbed Connector for .118 ID X .187 OD Microtube

  • A123

    3/4" FPT x 1/2" (17 mm) Barbed Ball Valve

    Regular Price:

    $2.86

    The 3/4” female pipe thread (FPT) x 1/2” barb ball valve is used as on/off valve for a drip tubing or drip line lateral. The ball valve can be used with individual 1/2” drip tubing with .700 OD and 17 mm drip line with a .670 OD.

    We make this ourselves out of three different products because no manufacturer produces this item. We got asked quite a bit for this configuration and instead of telling people to buy three different items we assemble them ourselves and sell it as one product.

  • PV103

    1" PVC Ball Valve / Slip x Slip

    Regular Price:

    $7.00

    1" PVC Ball Valve / Slip x Slip

    This ball valve comes in handy when you need to isolate sections of your irrigation supply line for maintenance. We always recommend to install a ball valve before any automated valve manifold which controls your irrigation zones.

    If you need to replace a valve, repair a valve or move a valve having one of these before the manifold is worth every penny.

  • PV102

    3/4" PVC Ball Valve / Slip x Slip

    Regular Price:

    $5.00

    3/4" PVC Ball Valve / Slip x Slip

    This ball valve comes in handy when you need to isolate sections of your irrigation supply line for maintenance. We always recommend to install a ball valve before any automated valve manifold which controls your irrigation zones.

    If you need to replace a valve, repair a valve or move a valve having one of these before the manifold is worth every penny.

  • PV101

    1/2" PVC Ball Valve / Slip x Slip

    Regular Price:

    $4.10

    1/2" PVC Ball Valve / Slip x Slip

    This ball valve comes in handy when you need to isolate sections of your irrigation supply line for maintenance. We always recommend to install a ball valve before any automated valve manifold which controls your irrigation zones.

    If you need to replace a valve, repair a valve or move a valve having one of these before the manifold is worth every penny.

  • SF001

    1/4" Barbed Connector

    Regular Price:

    $0.08

    1/4" Barbed Connector for .156 ID X .245 OD microtube

    This barb can be used to connect 1/4" microtube or 1/4" dripperline to a 1/2" or larger poly tube main line. Also for splicing any 1/4" tube together.

    If you have more that 5 or 6 of these to place into the 1/4" tube then take our advice and check out the A034. This is a gun style tool that inserts the barb into 1/4" microtube......WOW! It blew us away the first time we used it. You and your fingers will thank us!

    Check the "Related Products" section below.

  • SF003

    1/4" Barbed Tee

    Regular Price:

    $0.09

    1/4" Barbed Tee for .156 ID X .245 OD Microtube

    For connecting to any 1/4" tube or 1/4" tube to 1/2" tube.

    We have a tool (A034) that will connect TWO ends of this barb over microtube. We feel it is worth it and after you install a few of these you will understand.

  • SF004

    1/4" Barbed Elbow

    Regular Price:

    $0.09

    1/4" Barbed Elbow for any 1/4" microtube.

    Works on any microtube with an ID of .140 to .170

    For making sharp turns with 1/4" microtube. This really helps when you lay out tubing for potted plants.

    If you have a handful of these to install take a look at the A034 tool that installs microtube over BOTH ends of the barb. Your fingers will thank you!

    Look at the SF012 on the "Related Products" below for a fantastic alternative to this elbow!

  • A132

    1/2" MPT Triple Elbow

    Regular Price:

    $1.29

    Made of durable black plastic, the triple elbow with 1/2" male pipe thread is used to add flexibility when installing a sprinkler or multi outlet drip emitter with 1/2" FPT base by providing adjustment of height and position to the device installed.

    We like to call these "Magic"! We use them to connect multi-outlet manifolds to PVC Tees which had 1/2"  sprinkler risers attached. We take out the sprinkler riser, install one of these and then the manifold. This helps keep the manifold near ground level.

  • P503

    1" x 18" Flexible PVC Coupling

    Regular Price:

    $7.10

    This Flexible coupling from Dura Plastics is just the ticket for landscape irrigation repair. Broken pipes at odd angles or buried pipes you cannot move to put in a solid PVC pipe. Going over roots or rocks and the list goes on!

    This 18" long coupling will allow you to repair quickly any break in PVC and best of all you do not need any other fittings as the ends have built in slip couplings for the rated size.

    BONUS ALERT: The ends not only serve as couplings for the rated size (1" goes over 1" PVC pipe) but they also work to go inside fittings the next size up! Yup, the 1/2" ends will fit into 3/4" fittings, the 3/4" ends go inside 1" Fittings and the 1" ends fit into 1-1/4" fittings.

    Not to be used in constant pressure applications!

  • P502

    3/4" x 18" Flexible PVC Coupling

    Regular Price:

    $6.00

    This Flexible coupling from Dura Plastics is just the ticket for landscape irrigation repair. Broken pipes at odd angles or buried pipes you cannot move to put in a solid PVC pipe. Going over roots or rocks and the list goes on!

    This 18" long coupling will allow you to repair quickly any break in PVC and best of all you do not need any other fittings as the ends have built in slip couplings for the rated size.

    BONUS ALERT: The ends not only serve as couplings for the rated size (3/4"" goes over 3/4"" PVC pipe) but they also work to go inside fittings the next size up! Yup, the 1/2" ends will fit into 3/4" fittings, the 3/4" ends go inside 1" Fittings and the 1" ends fit into 1-1/4" fittings.

    Not to be used in constant pressure applications!

  • P501

    1/2" x 18" Flexible PVC Coupling

    Regular Price:

    $4.75

    This Flexible coupling from Dura Plastics is just the ticket for landscape irrigation repair. Broken pipes at odd angles or buried pipes you cannot move to put in a solid PVC pipe. Going over roots or rocks and the list goes on!

    This 18" long coupling will allow you to repair quickly any break in PVC and best of all you do not need any other fittings as the ends have built in slip couplings for the rated size.

    BONUS ALERT: The ends not only serve as couplings for the rated size (1/2" goes over 1/2" PVC pipe) but they also work to go inside fittings the next size up! Yup, the 1/2" ends will fit into 3/4" fittings, the 3/4" ends go inside 1" Fittings and the 1" ends fit into 1-1/4" fittings.

    Not to be used in constant pressure applications!

  • SF012

    1/4" Clip-On Elbow With Nail

    Regular Price:

    $0.14

    Make 90 degree turns in 1/4" tubing without cutting the tube or having to insert barbs! This handy Clip-On elbow makes the 90 degree turn without crimping the tube. It also allows you to nail the elbow where you want it or just leave it loose. The Clip-On Elbow will hold the tubing if it is nailed to an object or not!

    Got patio plants in pots.....this is what you need.

    As an added bonus it INCLUDES the NAIL with each one! So if you want to nail or not what you get from us is ready to go.

  • A134

    1/2" FPT Coupling

    Regular Price:

    $0.30

    1/2" FPT Coupling

    Comes in handy for many conversions of PVC to thread or for some head assembly parts.

  • A018

    1/4" barbed inline valve

    Regular Price:

    $0.61

    1/4" barbed inline valve

    Can be used in any of our 1/4" micro tube.

    • Use it to shut off sections of micro tube going to potted plants that may need to be moved or on individual plants.
    • Use it to control sections of 1/4" dripperline or dripperline for each container.
    • Use it to adjust microsprinklers so they give the exact spray needed for each plant.

1 - 16 of 226

Page:
  1. 1
  2. 2
  3. 3
  4. 4
  5. 5